View more the latest threads:

• Mobile services are close car trackers will not work for...
• PTA order to close all night packages in Pakistan mobile...
• Latest Kwick Provides World Category Regionally Produced...
• PTCL’s Landline Plus Packages detail April 2012
• Wi-tribe Announced Trip to Skardu Winners name April 2012
• PTCL Launches Smartphone EVODROID April 2012
• how to get free mobile balnace with internet 2012
• wi-tribe offer live streaming offer in pakistan 2012
• PTCL Gives Free WiFi Modem with new connection to customer...
• PTCL Vfone is CDMA prepaid and postpaid customers package...

PTCL introduces DSL service for our valued subscribers. We are committed to
provide you quality internet services. Please follow the installation instructions and
log on to your ADSL broadband link.
Step 1: Connecting to the Splitter, Power Connection & LAN cable.
1 Line hole connects to PTCL wire or Wall phone Jack (RJ-11 Jack).
2 Modem hole connects to the DSL jack of the ADSL CPE (Customer Premises
Equipment).
3 Phone hole connects to a telephone set.
4 Connect the Power Adapter to the AC power plug and attach the connector of
adapter to the CPE and switch it on.
5 Attach one end of LAN wire (RJ-45) to the LAN interface of CPE and the other
end to the LAN wire to the LAN interface of computer’s LAN card.
6 Link Indicator lights will lit up and show the connectivity. ADSL light will start
blinking and soon will be static as a sign of connectivity with our system, if the
line is properly jumpered in PTCL premises with the DSLAM (Digital
Subscriber Line Access Multiplexer).Joint less and direct cable line from the
nearest PTCL pole or cabinet must be connecting to your splitter and then all
the phone extensions must be taken from the phone hole of splitter. The Drop
wire distance from PTCL pole or Cabinet must not be ideally more than 50
meters.(Twisted pair wire can be longer)
Step 2: ADSL Configuration in CPE and Computer
1. Go to Start Menu < Control Panel < Network and Internet Connections < Network
Connections. Check that the Local Area Connection is enabled. Right click local
Area network and click properties. Following window will be shown.
Only the registered members can see the link. Register here
2. Double click “internet protocol (TCP/IP)”, Check “Use the following IP
address” and make the following settings:
IP Address: 192.168.1.3
Subnet Mask: 255.255.255.0
Gateway: 192.168.1.1
Then, check “Use the following DNS server addresses” and make
the following settings:
Preferred DNS Server: 203.99.163.240
Alternate DNS Server: 203.135.0.170
Only the registered members can see the link. Register here
3. Now open Internet Explorer and write “192.168.1.1” in address bar and press
enter. There must not be any proxy setting in the internet Explorer.
Only the registered members can see the link. Register here
A small pop up window will open as shown in the figure below and ask ”User Name”
and “Password” for opening the CPE’s interface.
Enter User Name: “admin” and Password: “admin” and press OK.
Only the registered members can see the link. Register here
4. Following page will be displayed after entering correct User name and Password:
Only the registered members can see the link. Register here
5. Click the Device Info link on the left hand side tabs, more options will be shown. Click
Statistics and further more options will be shown, among them select ADSL.
Only the registered members can see the link. Register here

6. Clicking ADSL will show the ADSL line parameters, Note the SNR Margin and Line
Attenuation. SNR must be higher than 08 dB and Line Attenuation must be less than 45
dB for establishing a stable DSL connection.
Only the registered members can see the link. Register here
Only the registered members can see the link. Register here7. Select “Advanced Setup” from the left hand tabs and following window will be displayed
Only the registered members can see the link. Register here
8. “Wide Area Network (WAN) Setup” window is shown displaying the list of default
connections. Check all of them except one and click remove button.

Only the registered members can see the link. Register here
9. Edit the connection by pressing the Edit button.
Only the registered members can see the link. Register here