CS501 Advance Computer Architecture midterm paper fall 2010

[Xpert]

MIDTERM EXAMINATION
Spring 2010
CS501- Advance Computer Architecture (Session - 5)

Time: 60 min
Marks: 38


Question No: 1 ( Marks: 1 ) - Please choose one
What is the instruction length of the SRC processor?

► 8 bits

► 16 bits

► 32 bits

► 64 bits


Question No: 2 ( Marks: 1 ) - Please choose one
Which one of the following is the memory organization of FALCON-E processor?

► 28 * 8 bits

► 216 * 8 bits

► 232 * 8 bits

► 264 * 8 bits


Question No: 3 ( Marks: 1 ) - Please choose one
“If P = 1, then load the contents of register R1 into register R2”.
This statement can be written in RTL as:

► R1 ¬ R2

► P: R1 ¬ R2

► P: R2 ¬ R1

► P: R2 ¬ R1, P: R1 ¬ R2


Question No: 4 ( Marks: 1 ) - Please choose one
The instruction ---------------will load the register R3 with the contents of the memory location M [PC+56]
►Add R3, 56
►lar R3, 56

►ldr R3, 56

►str R3, 56


Question No: 5 ( Marks: 1 ) - Please choose one
----------are faster than cache memory
►Accumulator register

►CPU registers

►I/O devices

►ROM



Question No: 6 ( Marks: 1 ) - Please choose one
P: R3 ¬ R5
MAR ¬ IR
These two are instructions written using RTL .If these two operations is to occur simultaneously then which symbol will we use to separate them so that it becomes a correct statement with the condition that two operations occur simultaneously?

► Arrow ¬

► Colon :

► Comma ,

► Parentheses ()


Question No: 7 ( Marks: 1 ) - Please choose one
Prefetching can be considered a primitive form of-------------
►Pipelining [/url]

►Multi-processing

►Self-execution

►Exception


Question No: 8 ( Marks: 1 ) - Please choose one
The processor must have a way of saving information about its state or context so that it can be restored upon return from the -------------
►Exception

►Function

►Stack

►Thread


Question No: 9 ( Marks: 1 ) - Please choose one

Which one of the following circuit design levels is called the gate level?

►Logic Design Level

►Circuit Level

►Mask Level

►None of the given


Question No: 10 ( Marks: 1 ) - Please choose one
__________ enable the input to the PC for receiving a value that is currently on the internal processor bus.
► LPC
► INC4
► LC
► Cout

Question No: 11 ( Marks: 1 ) - Please choose one
________ operation is required to change the processor’s state to a known, defined value.
► Change
► Reset
► Update
► None of the given

Question No: 12 ( Marks: 1 ) - Please choose one
There are _________ types of reset operations in SRC
► Two
► Three
► Four
► Five

Question No: 13 ( Marks: 1 ) - Please choose one
_____________ controller controls the sequence of the flow of microinstructions.
► Multiplexer
► Microprogram
► ALU
► None of the given

Question No: 14 ( Marks: 1 ) - Please choose one
FALCON-A processor bus has 16 lines or is 16-bits wide while that of SRC is __________ wide.

► 8-bits
► 24-bits
► 32-bits
► 64-bits

Question No: 15 ( Marks: 1 ) - Please choose one
Which of the following statement(s) is/are correct about Reduced Instruction Set Computer (RISC) architectures.
(i) The typical RISC machine instruction set is small, and is usually a subject of a CISC instruction set.
(ii) No arithmetic or logical instruction can refer to the memory directly.
(iii) A comparatively large number of user registers are available.
(iv) Instructions can be easily decoded through hard-wired control units.

► (i) and (iii) only
► (i), (iii) and (iv)
► (i), (ii) and (iii) only

► (i),(ii),(iii) and (iv)


Question No: 16 ( Marks: 1 ) - Please choose one
Which one of the following register holds the instruction that is being executed?







► Accumulator
► Address Mask
► Instruction Register
► Program Counter

Question No: 17 ( Marks: 2 )
Write the following statement of an Arithmetic Instruction using RTL.
If op-code is 0, the instruction is ‘add’. The values in register rb and rc are added and the result is stored in register rc
[url=http://vustudents.ning.com]

Question No: 18 ( Marks: 2 )
Given below are the various fields of an SRC instruction register.
a) operation code field : op<4..0>
b) target register field : ra<4..0>
c) operand, address index, or branch target register : rb<4..0>
d) second operand, conditional test, or shift count register: rc<4..0>

Rewrite these various fields of an SRC instruction, using the RTL.